This is a 5/16" Head Split Rivet - Zinc Plated. Used to install FS-118 Hood Lace onto the radiator shell. Approximately 20 used per radiator shell. Specific Applications: 1929-1932 Passenger Cars; 1929-1933 Trucks

This is Hood Lace without Wire for 1929-1933 Chevrolet cars & trucks. Used on many GM vehicles in this era. This hood lace is held in place with split rivets FS-11683 - sold separately. This Hood Lace is sold by the foot. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.

This is a set of hood lace hooks to be used with the hood lace with wire insert that was used on most GM vehicles from 1929-1939, including all Chevrolet cars & trucks. Each hook is designed to grab the wire that is inserted inside the hood lace and draw it tight to insure a clean installation. These are an exact match to the original hooks. They have a threaded shaft and come with a nut for tension. Replaces GM# 355568

Not an original item but can be used on any vehicle. Comes with two rivets.

These rubber bumpers fit all 1929-1932 Chevrolet cars & trucks. They mount into the hood roll at the bottom edge of the hood side at the front and rear of the hood. We recommend gluing them in place with a small dab of clear silicone sealer to prevent them from falling out if they get bumped. Diameter of the head of the bumper is 5/16", shaft diameter 3/16", overall length 3/4".

This is a completely new reproduction of the original Cowl Hood Lace with Wire Insert that was used on most GM vehicles from 1929-1939, including all Chevrolet cars & trucks. Design & engineering took over a year to get an exact match. The material is a dark brown, close to black. Proper contours & beads that match original samples perfectly. Each strip is 3/4" Wide x 48" Long of fabric with a 52" wire inserted into it. Cut to length as required. NOTE: The hood lace is sold in individual 48" strips to fit most cowl applications. Mid-thirties cars also used this material on the radiator shell. To accommodate mid 30's vehicles where short sections are required on radiator shells, order one extra piece. ORDER TWO PIECES IF DOING A COWL AND A THIRD PIECE IF NEEDED ON THE RADIATOR SHELL. Early cars used hood lace without wire on the radiator shell. Order tension hooks AF-277 or clips set DS-106R separately. Made in the USA! Replaces GM# 374969.

This hood hinge hold down mounts to the radiator shell on 1932 Chevrolet Passenger cars and 1933 Chevy Trucks. This hold down is stamped in stainless. Made in the USA!

1929-32 Passenger & 1929-33 Truck. 1EA 1/4" x 33-1/8" 2EA 3/16" x 31-5/16"

1932 Chevy passenger car hood vent door spring set. This set of 16 springs is made of stainless steel so they won't rust. Set includes 8 top and 8 bottom springs - complete set for one hood. All 1932 Chevrolet passenger cars. Replaces GM# 368795, 368796

This is a 8-piece set of beautifully chromed Hood Door Finger Pulls for 1932 Chevrolet passenger cars. These beautiful reproductions of the original chrome pieces will make your 1932 Chevy shine like it should! The precision die-cast pulls are triple chrome plated to a show quality finish. They are super detailed and absolutely stunning! Overall Length is 3-3/4" Long. 1932 Pulls are sold in sets of eight (8) pieces. They come with mounting screws ready to install. In stock and ready for immediate shipment. You can buy with confidence as we have been serving the hobby since 1979 and we are the manufacturer of this great item. Replace those old original, pitted pulls with this show quality set. Get yours today! Replaces GM# 367450

LIMITED SUPPLY - This item has been discontinued by our supplier. Availability subject to stock on hand. This a new Set of 8 Hood Doors made in Plain Steel for all 1932 Chevrolet passenger cars. These hood doors are made from precision tooling and are an exact match for the originals. Plain steel doors are great for painting or chrome plating. Nice, smooth steel with no rust pits! Replaces GM# 363749, 367894

This is a set of Hood Latch Bracket for 1932 Chevrolet Passenger Cars & 1933 Chevrolet Trucks. Set of four pieces for the Cowl & Radiator Shell. These are the brackets that hold the ends of the locking rods in place. One set required per vehicle.

This is a BLACK 4 piece Hood Latch Set for early Chevrolet cars & trucks. They are correct for all 1931 cars & trucks and also 1932 Chevy trucks. They will work on all 1929-1932 trucks and 1929-1931 passenger cars by using the correct forked hooks on the hood (GR-150). The hooks that go on the hood are sold separately. Overall Height in relaxed position: 5-1/4" - Extended Length 6-1/4". Replaces GM# 357092, 365848. Another quality part made by The Filling Station.

This is a CHROME 4 piece set of hood latches for early Chevrolet cars & trucks. They are correct for all 1931 cars & trucks and also 1932 Chevy trucks. They will work on all 1929-1932 trucks and 1929-1931 passenger cars by using the correct forked hooks on the hood (GR-150). The hooks that go on the hood are sold separately. Overall Height in relaxed position: 5-1/4" - Extended Length 6-1/4". Replaces GM# 357092, 365848. Another quality part made by The Filling Station.

This universal hood prop kit mounts on the radiator support "V" rod that mounts to the firewall. Used on cars & trucks with 4-piece hoods. Holds one side of the hood open at a time. These stainless kits make holding the hood open an easy task.