This is the SMALL Rubber Front Motor Mount Cushion for 1955-1962 Chevrolet & GMC cars & trucks. Dimensions: 7/16" ID x 1-1/2" OD. Four pieces required per vehicle. Replaces GM# 3714358 Specific Applications: 1955-1957 Passenger; 1955-1959 (2nd Series) Series 3 Commercial & Utility; 1960-1962 Series 20-30 Dubl-Duty
For 1955 1956 1957 1958 1959 1960 1961 1962 Chevrolet Cars and Trucks
This is the LARGE Rubber Front Motor Mount Cushion for 1955-1962 Chevrolet & GMC cars & trucks. Dimensions: 7/16" ID x 2" OD. Four pieces required per vehicle. Replaces GM# 3714357 Specific Applications: 1955-1957 Passenger; 1955-1959 (2nd Series) Series 3 Commercial & Utility; 1960-1962 Series 20-30 Dubl-Duty
For 1955 1956 1957 1958 1959 1960 1961 1962 Chevrolet Cars and Trucks
This metal motor mount grease shield fits 1933-1955 1st series Chevrolet and GMC trucks. Dimensions: 7-15/16" x 2-1/2", Replaces GM # 3656502. Specific Applications: 1933-1955 1st Series: Chevrolet 1/2 Ton - 2 Ton 1939-1955 1st Series: GMC 1/2 Ton - 3 Ton
This is a set of LOWER REAR motor mounts for 1954-1982 Chevrolet & GMC trucks. These mounts sit under the bell housing cross member. Also see FS-322 upper mounts. Replaces GM# 3789949, 3705447 Specific Applications: 1954-1955 (1st Series) All Commercial & Utility; 1955-1982 (2nd Series) 1/2 Ton thru 2 Ton Utility Trucks
This is the rubber cushion for the front motor mount for 1932-1955 Chevrolet & GMC cars & trucks. Rubber is to be mounted with slots facing upward. Replaces GM# 3657520, 3739939 Specific Applications: 1932 Chevrolet Passenger - Mounts under the cross member; 1933-1955 (1st Series) Chevrolet & GMC Trucks with 6-Cylinder
For 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 1955 Chevrolet Cars and Trucks
This is a set of UPPER REAR motor mounts for 1954-1982 Chevrolet & GMC trucks. These mounts sit on top of the bell housing cross member. Also order FS-323 lower mounts. Replaces GM# 3705444 Specific Applications: 1954-1955 (1st Series) All Commercial & Utility; 1955-1982 (2nd Series) 1/2 Ton thru 2 Ton Utility Trucks
This is a set of LOWER motor mount cushions for 1952-1954 Chevrolet passenger cars, including Sedan Delivery. Sold as a pair for both sides. Order CV-229 upper mounts separately. Replaces GM# 3700332
For 1952 1953 1954 1955 1956 1957 1958 1959 1960 1961 1962 Chevrolet Cars
This is a set of UPPER motor mount cushions for 1952-1954 Chevrolet passenger cars, including Sedan Delivery. Sold as a pair for both sides. Order CV-230 lower mounts separately. Replaces GM# 3702889
These are the rear motor mounts - Left & Right - for 1955-1957 Chevrolet passenger cars with standard transmission. Replaces GM# 3713427, 3728507, 3728508, 3735063, 3735064, 3746297, 3746298 Specific Applications: 1955-1957: Passenger except Powerglide 1957: Turboglide only except Convertible
This is a set of REAR motor mounts for 1947-1953 Chevrolet 1/2 Ton Trucks. Double steel core with molded rubber cushion. Compare to CV-227. Replaces GM# 756700
For 1947 1948 1949 1950 1951 1952 1953 Chevrolet Trucks
These are the rear motor mounts - Left & Right - for 1955-1957 Chevrolet passenger cars with automatic transmission. Replaces GM# 3725285, 3725286, 3729423, 3729424 Specific Applications: 1955: All passenger with Powerglide 1956-1957: All with automatic transmission (except convertible) 1956-1957: Convertible with Powerglide
This is a set of REAR motor mounts for 1937-1953 Chevrolet Trucks. Double steel core with molded rubber cushion. Compare to CV-226. Replaces GM# 595741, 3702198, 3702173 Specific Applications: 1937-1947: All commercial (exc 1947 1/2 ton 2nd design); 1948-1953: All commercial (exc 1/2 Ton); 1939-1953: GMC 1/2 to 2 ton
For 1937 1938 1939 1940 1941 1942 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 Chevrolet Trucks
This engine side motor mount set fits 1935-1948 Chevrolet passenger cars. This rectangular shaped mount should be compared to CV-224 side motor mounts that are "E" shaped. Mounts fit Right or Left on the side frame bracket to clutch housing bracket. 2 per car - sold in pairs. Replaces GM# 377928
For 1935 1936 1937 1938 1939 1940 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
This engine side motor mount set fits 1935-1948 Chevrolet passenger cars, except Cabriolet. This "E" shaped mount should be compared to CV-295 side motor mounts that have a single hole in the center on top and bottom in the middle. Mounts fit Right or Left on the side frame bracket to clutch housing bracket. 2 per car - sold in pairs. Replaces GM# 756056, 756057, 3692162
For 1935 1936 1937 1938 1939 1940 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
This is a front motor mount kit for 1955-1957 Chevrolet passenger cars. Contains two (2) shafts washers & cushions for replacing front motor mounts on V8 models.
This is a set of FRONT Engine Mounts for 1955-1959 Chevrolet Trucks with V-8 Engines. Includes engine and cross member brackets - and all link parts. This is an exact reproduction of the original factory mounts. Use with FS-322 & FS-323 rear mounts for a complete installation.
1949-1954 Chevrolet Passenger Car V-8 Engine Conversion Kit. This motor mount conversion is designed for mounting a small block Chevy V-8 engine into 1949-1954 Chevrolet passenger cars. It also will work for Chevy V-6 engines with distributor at the rear. Kit comes with brackets for frame and engine, black polyurethane motor mount cushions, hardware and instructions.
This is a Lower Front Motor Mount for 1957-1959 Chevrolet trucks. See also 25-63 upper. Replaces GM# 572858, 759530, 761748 Specific Applications: 1957: 8 cyl (up to 350CID) 1958-59: 8 cyl (336 & 347CID)
1955-61 Motor mount, upper, engine bracket at front cross member. One (1) per vehicle. New rubber vulcanized to your old steel core. Send your metal piece and allow 3 weeks. GMC Truck only. See 25-73 for lower. 1955-59: 8 cyl GMC 1960-61: V-6 & V-12 GMC
1955-61 Insulator, engine mount, front lower. Re-vulcanizing service only. Send in your complete engine mount and allow 3 to 4 weeks for service. For mounts #759385, #572945, & #761748 as used on: 1955-59: 8 cyl GMC 1960-61: V-6 & V-12 GMC
1960-62 Motor mount, front support. Replaces #3763767. New rubber vulcanized to your old core. Please send in your old steel cores and allow 3 weeks for delivery. For Series 10-40 Trucks without Powerglide
1933-34 Insulator, motor support, front. Replaces #371252. New rubber vulcanized to your old steel core. Send original steel casing and core. THIS IS A REVULCANIZING SERVICE ONLY - CUSTOMER MUST SEND IN ORIGINAL CORES FOR SERVICE.
1934 Cushion, motor mount, side. Replaces #375630. New rubber vulcanized to original steel cores. Send your old steel cores when ordering. Allow 3 weeks for service. Two (2) per car. DA Master only. This is a Revulcanizing Service only. We must have your original metal cores for rebuild.
THIS IS A REVULCANIZING SERVICE - YOUR METAL CORES MUST BE PROVIDED. 1933: Master CA (Eagle) 1934: Standard DC New rubber vulcanized to original steel cores. Please send your old steel cores when ordering. Two (2) per car. Please allow 3 weeks for service.
1934 Motor mount, front (engine front support). Re-vulcanizing service. Two (2) reqired per car. Replaces #375623. Send in both parts of your old motor mounts. We clean and re-vulcanize them with new rubber. Allow 3 weeks for service. Master (DA) Series only.
1936-51 Cushion, engine mount, front. Re-vulcanization service only on #3659291. Send in your rebuildable cores when ordering. Allow 3 weeks for service. Also see CV-241 1936-39: Models FC, GB, HB, JB 1941-48: Passenger except convertible 1950-51: Passenger with Powerglide
For 1936 1937 1938 1939 1940 1941 1942 1944 1945 1946 1947 1948 1949 1950 1951 Chevrolet Cars
These are rear motor mounts (on bell housing) for 1932-1936 Chevrolet cars & 1/2 Ton Trucks. This is a re-vulcanizing service which puts new rubber into YOUR original metal cores. We must have your original pieces to rebuild. Replaces GM# 836805 Specific Applications: 1932 Passenger & Sedan Delivery; 1933 Standard Passenger & Sedan Delivery; 1933-1936 1/2 Ton Trucks THIS IS A RE-VULCANIZING SERVICE ONLY - PUTS NEW RUBBER INTO YOUR ORIGINAL METAL CORES. Send your steel cores (2 pieces per support) allow 3-4 weeks for service. Contact us if you do not have cores - we may have used parts available at additional cost.