86 Items Found
Division Bar Channel
CHEVROLET 1973-1980 TRUCK DIVISION BAR CHANNEL
1973-1980 Chevrolet & GMC Truck Vent Window Division Bar Channel. The glass run channel presses into the vertical division bar channel. This single piece fits either the driver or passenger doors. Our product is made from the original specs and from high quality ozone resistant materials to fit your vehicle.
For 1973 1974 1975 1976 1977 1978 1979 1980 Chevrolet Trucks
Mounting Pads
CHEVROLET 1932-35 PAD W'SHIELD LOWER W'STRIP
1932-35 Pad, windshield lower weather strip, retainer to cowl. Forty-four (44) inches per strip. Roadster and Phaeton only. With nine (9) pre-drilled holes
For 1932 1933 1934 1935 Chevrolet Cars
Windshield Bumpers
CHEVROLET 1936-1938 PU WINDSHIELD REGULATOR SEAL
This windshield regulator crank handle seal fits 1936-1938 Chevrolet & GMC truck. Installed in the dash where the crank-out windshield hand crank is mounted. Replaces GM# 304704 Sheet Metal Hole: 1-3/32" Center Hole: 7/8" Outside Diameter: 1-7/16" Slot Width: 1/16"
For 1936 1937 1938 Chevrolet Trucks
CHEVROLET 1936-1938 PASS SIDE WINDOW ANTI-RATTLE PAD
1936-1938 Chevrolet Passenger Car Anti-rattle, rubber, side window, inner and outer. Dimensions: 3/4" Long x 15/32" High. Replaces #4072911. Fits slot in outer door body metal and inner window frame (garnish molding). Closed models. It can also be used as a close replacement for 1937-1938 Glove Box Door Bumper. NOTE: This bumper will also work as a very close replacement for 1931 Chevrolet Passenger Car Windshield Center Bumper. It will have to be cut down to fit, but otherwise is an excellent substitute for this bumper. Recommend cutting slightly longer than the slot hole to make a tight fit. Specific Applications: 1936-1938 Passenger Side Window Anti Rattle Bumper; 1937-1938 Passenger Glove Box Bumper - Replacement; 1931 Passenger Windshield Center Bumper on Dash - Replacement on Closed Cars
For 1931 1932 1933 1934 1935 1936 1937 1938 Chevrolet Cars
CHEVROLET 1937-1946 TRUCK WINDSHIELD BUMPERS
This is a pair of Windshield Bumpers for 1937-1946 Chevrolet & GMC trucks with swing-out windshield. Mounts against dash. This is a Rubber part with Steel core, 9/16” x 5/16” thick. Two per vehicle. Made in the USA! Replaces #3681093
For 1937 1938 1939 1940 1941 1942 1944 1945 1946 Chevrolet Trucks
Windshield Division Bar
CHEVROLET 1941-48 DIVISION BAR RETAINER SEAL
1941-48 Retainer, rubber, for outside windshield center post stainless molding. Use with original stainless molding and clips
For 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1939 WINDSHIELD DIVISION BAR SEAL
This windshield division bar gasket set fits all 1939 Chevrolet passenger cars. Two (2) piece set for inner and outer, molded with holes and pilots. This set is used with 70-601 vulcanized channel for complete windshield installation. All closed models. Replaces GM# 4089925, 4089926.
For 1939 Chevrolet Cars
CHEVROLET 1937-38 WINDSHIELD DIVISION BAR
1937-38 Gasket Windshield division post, inner and outer. Retains outer division bar chrome molding. Steel core, threaded as original for screws.
For 1937 1938 Chevrolet Cars
CHEVROLET 1939-46 PU WINDSHIELD DIVISION BAR
SCREW SIZE FOR DIVISION BAR SCREWS: 10-32 1939-46 Division bar rubber, swing-out windshield. Inner and outer rubber with threaded steel core as original. 2 piece set for all Truck models.
For 1939 1940 1941 1942 1944 1945 1946 Chevrolet Trucks
Windshield Post Weatherstrip
Windshield Seal
CHEVROLET 1947-53PU WINDSHIELD SEAL-NO REVEAL
The windshield channels are vulcanized one-piece units with division bar rubber molded into the ring. When listed as "no reveal or "reveal" models, this indicates whether the vehicle originally came with stainless molding around the windshield gasket. See manufacturer's installation video: Click here to view Replaces GM# 3684802 Specific Applications: 1947 - 1953 Chevrolet - Truck 1947 - 1949 GMC - 150-22 1947 - 1950 GMC - FC101 1947 - 1950 GMC - FC102 1947 - 1950 GMC - FC152 1947 - 1950 GMC - FC251 1947 - 1950 GMC - FC252 1951 - 1953 GMC - 150-22 1951 - 1953 GMC - 250 1951 - 1953 GMC - 250-22 1951 - 1953 GMC - 280-22 1951 - 1953 GMC - 300 1951 - 1953 GMC - 350-24 1951 - 1953 GMC - 350-27 1951 - 1951 GMC - P152 1952 - 1953 GMC - 102-22 1952 - 1953 GMC - 253-22 1952 - 1952 GMC - FC100-22 1952 - 1953 GMC - PM152-22 1953 - 1953 GMC - 100-22
For 1947 1948 1949 1950 1951 1952 1953 Chevrolet Trucks
CHEVROLET 1947-53PU WINDSHIELD SEAL W/REVEAL
This is a Windshield Seal for 1947-1953 Deluxe Chevrolet & GMC Trucks with Stainless Reveal Moldings This windshield channel is a vulcanized one-piece unit with division bar rubber molded into the ring. When listed as "no reveal or "reveal" models, this indicates whether the vehicle originally came with stainless molding around the windshield gasket. Reuse your original stainless trim or purchase new trim to be used with "Reveal" molding seals. See manufacturer's installation video: Click here to viewReplaces GM# 3684695
For 1947 1948 1949 1950 1951 1952 1953 Chevrolet Trucks
Windshield Seals
CHEVROLET 1926-36 WINDSHIELD/DOOR WINDOW SEAL
1926-36 Seal, lower side window. Fastens to inner face of door to seal against outer side of glass. 1926-31 Seal. Crank-up windshield top. L-shaped strip fastens to windshield header facing glass to seal across top. Many models with crank-up windshield. Approximately four (4) feet required per windshield. Many models Fastens to windshield header facing glass to seal across top. Many models with crank-up windshields. Approx. 4ft. required per windshield. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.
For 1926 1927 1928 1929 1930 1931 Chevrolet Cars and Trucks
CHEVROLET 1914-1935 WINDSHIELD WEATHERSTRIP 1-1/2 INCH
1914-35 Weatherstrip, largest type of T-rubber. 1-1/2” high. For many applications but especially between the windshield frame and cowl on open cars. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.
For 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 Chevrolet Cars and Trucks
CHEVROLET 1920-1935 CAR & TRUCK WINDSHIELD SEAL - 1 INCH
1920-30 Weather-strip. T-rubber. 1” high with 9/32” top. Various applications, earlier windshields. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.
For 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 Chevrolet Cars and Trucks
CHEVROLET 1920-35 CAR/TRUCK WINDSHIELD SEAL - 3/4 INCH
1920-35 Windshield Weatherstrip. T-rubber. 3/4” high with 5/16” top. Various applications for roadster, touring & truck windshields. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.
For 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 Chevrolet Cars and Trucks
CHEVROLET 1937-1948 WINDOW CHANNEL - NO REVEAL
This is an extruded rubber channel for setting windshield & back glass in 1937-1948 GM passenger cars. This channel is designed for windows without chrome reveal molding. 8 to 12 feet required per window. Sold by the foot, order as required. Compare cross section illustration to your original rubber seal. See also vulcanized, one piece windshield & rear window channels. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.
For 1937 1938 1939 1940 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1934-1936 WINDOW CHANNEL-NO REVEAL
This is an extruded rubber channel for setting windshield & back glass in 1934-1936 GM passenger cars. This channel is designed for windows without chrome reveal molding. 8 to 12 feet required per window. Sold by the foot, order as required. Compare cross section illustration to your original rubber seal. See also vulcanized, one piece windshield & rear window channels. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.
For 1934 1935 1936 Chevrolet Cars
CHEVROLET 1940-48 WINDOW CHANNEL-WITH REVEAL
This is an extruded rubber channel for setting windshield & back glass in 1940-1948 GM passenger cars. This channel is designed for windows without chrome reveal molding. 8 to 12 feet required per window. Sold by the foot, order as required. Compare cross section illustration to your original rubber seal. See also vulcanized, one piece windshield & rear window channels. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.
For 1940 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1933-34 WINDOW CHANNEL-NO REVEAL
1933-34 For windows with or without reveal molding. 8 to 12 feet required per window. Note: we cannot furnish channels with the stainless bead molding for those cars so equipped. This is the closest we can come. See also vulcanized rear window channels. NOTE: This item is sold by the foot. Items that are cut to order are NOT RETURNABLE. Please insure this item is what you need BEFORE ordering.
For 1933 1934 Chevrolet Cars
CHEVROLET WINDSHIELD ADHESIVE COLD KNIFE CUTTING TOOL
This cold knife comes complete with a strong steel blade sharpened to a fine cutting edge. A large durable handle combined with a steel cable pull assures an easy and fast cutting of adhesive around windshields.
For 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 1929 1930 1931 1932 1933 1934 1935 1936 1937 1938 1939 1940 1941 1942 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 1959 1960 1961 1962 1963 1964 1965 1966 1967 1968 1969 1970 1971 1972 1973 1974 1975 1976 1977 1978 1979 1980 1981 1982 1983 1984 1985 1986 1987 Chevrolet Trucks
CHEVROLET 1936 PU WINDSHIELD RUBBER SEAL
This is a 10 foot long windshield seal for 1936-1946 Chevrolet & GMC trucks. In 1936, used on Low Roof Cabs only. Strip must be trimmed to length. For 1937-1946 Trucks, we offer a one-piece vulcanized seal - See 60-481 or 60-447
For 1936 Chevrolet Trucks
CHEVROLET 1929-1933 TRUCK WINDSHIELD SEAL
This windshield rubber comes in three pieces. Insert into windshield frame and glue the beveled corners with weatherstrip adhesive or Loctite super glue (available at most NAPA stores).
For 1929 1930 1931 1932 1933 Chevrolet Trucks
CHEVROLET 1934-35 TRUCK WINDSHIELD SEAL
This windshield rubber comes in three pieces. Insert into windshield frame and glue the beveled corners with weatherstrip adhesive or Loctite super glue (available at most NAPA stores). May need to be trimmed.
For 1934 1935 Chevrolet Trucks
CHEVROLET 1913-1928 WINDSHIELD WEATHERSTRIP
1913-28 Weatherstrip, for horizontally split windshields. Most 4-cylinder models. Almost universal application to open cars. Made to accommodate 1/4” glass. Approximately four (4) foot strip per windshield
For 1913 1914 1915 1916 1917 1918 1919 1920 1921 1922 1923 1924 1925 1926 1927 1928 Chevrolet Cars and Trucks
CHEVROLET 1941-48 WINDSHIELD PINCHWELD SEAL
1941-48 Pinchweld seal, windshield, to seal and retain outer reveal molding. Used with our 70-1192. Twelve (12) foot strip. Also used with reveal molding vulcanized windshield seals. For all Fisher bodies.
For 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1929-1932 LOWER WINDSHIELD SEAL - OPEN CARS
This Windshield Gasket is made of a high-quality EPDM dense rubber extrusion. This four (4) foot strip mounts on the lower windshield for easy installation. This seal is used on 1929-1932 Roadster & Phaeton only. Made from top quality rubber to ensure durability and proper seal. Designed from original part so it fits correctly. Glass channel manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and Made in the USA.
For 1929 1930 1931 1932 Chevrolet Cars
CHEVROLET 1939-46 TRUCK WINDSHIELD SEAL
1939-1946 Chevrolet & GMC Trucks with swing out windshields. This is the seal on outer edge of frame.
For 1939 1940 1941 1942 1944 1945 1946 Chevrolet Trucks
CHEVROLET 1961-62 CAR GUTTER SEAL LOWER W/S
1961-62 Gutter, windshield lower corner, left and right. Rubber with metal core as original. Replaces #4817250 & 4817251. For full size passenger models.
For 1961 1962 Chevrolet Cars
CHEVROLET 1937-38 TRUCK WINDSHIELD SEAL
This rubber seal is a one-piece ring that fits on the outer edge of the windshield frame on all Chevrolet & GMC trucks with swing-out windshields. Top quality USA-Made rubber.
For 1937 1938 Chevrolet Trucks
CHEVROLET 1947-53 WINDSHIELD SEAL W/O DIV BAR
The windshield channels are vulcanized one-piece units without division bar rubber molded into the ring. This is for "V-butt" custom installations only.
For 1947 1948 1949 1950 1951 1952 1953 Chevrolet Trucks
CHEVROLET 1941-48 WINDSHIELD SEAL (W/REVEAL)
This windshield seal fits 1941-1948 Chevrolet passenger cars - Series 1000 with reveal molding except Style 1007 Aerosedan. Also requires 70-96 & 70-373 to complete installation. Refer to the Fisher Body Identification Plate on the firewall for specific Style number information. Reveal molding requires pinchweld seal 70-96. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. Replaces GM# 4114860, 4122594 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1941-48 WINDSHIELD SEAL W/O DIV BAR
1941-48: All 1200 series cars without reveal molding. NO DIVISION BAR This windshield seal is for the street rodder or custom car builder. Molded without the division bar so that the windshield can be "butted" together.
For 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1955 WINDSHIELD SEAL - NO REVEAL
This windshield seal fits all 1955 Chevrolet 150 Series passenger cars and sedan delivery. For windshields that do not have reveal molding. This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. Replaces GM# 4657625 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1955 Chevrolet Cars
CHEVROLET 1937-38 CAR WINDSHIELD SEAL
This windshield seal fits all 1937-1938 Chevrolet closed body cars. This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. Fitted gasket provides a formed, seamless seal. Designed from original part so it fits correctly. Order division bar 70-159 separately. Replaces GM# 4073730, 4073737, 4089916 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1937 1938 Chevrolet Cars
CHEVROLET 1955-1957 CAR WINDSHIELD SEAL
This windshield seal fits all 1955-1957 Chevrolet passenger cars - Series 210 and Bel Air (except convertible). This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding. Fitted gasket provides a formed, seamless seal and accommodates reveal molding. Designed from original part so it fits correctly. Replaces GM# 4663515. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1955 1956 1957 Chevrolet Cars
CHEVROLET 1955-57 CONVERTIBLE WINDSHIELD SEAL
This windshield seal fits 1955-1957 Chevrolet Convertibles only. This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the top edge's decorative molding. Replaces GM# 4650350 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1955 1956 1957 Chevrolet Cars
CHEVROLET 1926-1931 CHEVY & GM CAR WINDSHIELD SEAL SET
This is a windshield seal set for 1926-1931 Chevrolet passenger cars. Also fits other GM passenger cars with Fisher Bodies - Pontiac, Oldsmobile, Buick, Cadillac, Durant and Oakland - not for convertible models. Three piece set for the bottom and sides. Also order 4 ft. of 70-64 for the top seal - sold separately. Top quality rubber - Made in the USA!
For 1926 1927 1928 1929 1930 1931 Chevrolet Cars
CHEVROLET 1933-1935 CAR WINDSHIELD SEAL
This windshield seal fits 1933-1935 Chevrolet passenger cars (except 1935 Master Deluxe). Note: 1933 Master cars had a stainless trim imbedded in the rubber seal. While this seal will replace the old one but it does not accept the stainless trim. This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. Fitted gasket provides a formed, seamless seal. Designed from original part so it fits correctly. Replaces GM# 4045691. Specific Applications: 1933-1934: All closed models without reveal molding 1935: All series 1200 Standard Models without reveal molding Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1933 1934 1935 Chevrolet Cars
CHEVROLET 1935 MASTER-36 ALL WINDSHIELD SEAL-NO REVEAL
This windshield seal fits 1935 & 1936 Chevrolet passenger cars. This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. Fitted gasket provides a formed, seamless seal. Designed from original part so it fits correctly. Replaces GM# 4058826. Specific Applications: 1935: Chevolet Passenger Cars - Styles 1001, 1009, 1011, 1017, 1019, 1057 1936: All closed models Master & Standard Refer to the Fisher Body Identification Plate on the firewall for specific Style number information. Order 70-59 division bar separately Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA.
For 1935 1936 Chevrolet Cars
CHEVROLET 39-48 CAR WINDSHIELD SEAL-NO NOTCH
1939: All Pass. NOTE: in 1939 models you must measure the developed length before ordering. This seal is 115" long but 1939 had three different lengths possible: 110", 112" & 115". Owners of 1939 models must specify length if you want anything other than 115". 1940: 1200 & 1500 series 1942-48 Fleetline AeroSedan 1007 without reveal molding - NO DIVISION BAR This windshield seal is for the street rodder or custom car builder. Molded without the division bar so that the windshield can be "butted" together.
For 1939 1940 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1939 CAR WINDSHIELD SEAL
1939 All closed bodies. Order 60-39 division bar separately Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1939 Chevrolet Cars
CHEVROLET 1963-64 IMPALA H/T WINDSHIELD SEAL
Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1963 1964 Chevrolet Cars
CHEVROLET 1932 WINDSHIELD SEAL-4 PIECE SET
This is a four piece set of rubber to seal the windshield on all 1932 Chevrolet closed cars with crank-up windshields. Set includes two side channels with felt covering, heavy lower seal that fits into the groove on the cowl below the windshield, and the long rubber seal that fits into the stainless trim on the top and sides.
For 1932 Chevrolet Cars
CHEVROLET 1958 IMPALA 2DR HARDTOP WINDSHIELD SEAL
This windshield seal fits 1958 Chevrolet Impala 2-Door Hardtop - Style 1847 Only. This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding. Fitted gasket provides a formed, seamless seal and accommodates reveal molding. Designed from original part so it fits correctly. Replaces GM# 4714860. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1958 Chevrolet Cars
CHEVROLET 1937-38 CADILLAC WINDSHIELD SEAL
1942-48: Fleetline Aerosedan with reveal molding. NO DIVISION BAR. This windshield seal is for the street rodder or custom car builder. Molded without the division bar so that the windshields can be "butted" together. Order separately 70-96 pinch weld seal for stainless trim.
For Chevrolet Cars
CHEVROLET 1963-64 IMPALA WINDSHIELD SEAL
1963-64 Impala sport sedan (4-door hardtop) Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1963 1964 Chevrolet Cars
CHEVROLET 1958 (EXC 2DR HT/CVT) WINDSHIELD SEAL
This windshield seal fits all 1958 Chevrolet passenger car models (except styles 1847 1867 & Corvette) This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding. Fitted gasket provides a formed, seamless seal and accommodates reveal molding. Designed from original part so it fits correctly. Replaces GM# 4714578. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1958 Chevrolet Cars
CHEVROLET 63-64 IMPALA CONVERT W'SHIELD SEAL
Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1963 1964 Chevrolet Cars
CHEVROLET 1953-1954 HT/CONVT WINDSHIELD SEAL
This windshield seal fits 1953-1954 Chevrolet Convertibles & Hardtops - Styles 1037, 1037D & 1067, 1067D - models with reveal molding. This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding. Fitted gasket provides a formed, seamless seal and accommodates reveal molding. Designed from original part so it fits correctly. Replaces GM# 4601373 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1953 1954 Chevrolet Cars
CHEVROLET 1939-40 CADILLAC WINDSHIELD SEAL
1941-48: All 1000 series cars with reveal molding except 1007 Aerosedan. Custom cars only - NO DIVISION BAR This windshield seal is for the street rodder or custom car builder. Molded without the division bar so that the windshield can be "butted" together. Order separately 70-96 pinch weld seal for stainless trim.
For 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1961-62 CONVERTIBLE WINDSHIELD SEAL
1961-62 All full size convertibles Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1961 1962 Chevrolet Cars
CHEVROLET 1942-1948 AEROSEDAN WINDSHIELD SEAL
This windshield seal fits 1942-1948 Chevrolet Fleetline Aerosedan Style 1007 ONLY. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. This gasket requires external divider bar seal, part #70-373. Reveal molding requires pinchweld seal #70-96. Fitted gasket provides a formed, seamless seal. Designed from original part so it fits correctly. Replaces GM# 4125418. Order 70-96 & 70-373 separately. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1953-1954 SEDAN WINDSHIELD SEAL-REVEAL
This windshield seal fits 1953-1954 Chevrolet Bel Air & 210 post coupes and all sedans, including station wagon & sedan delivery with reveal molding. Reveal molding is the stainless trim that inserts into the rubber windshield channel. Replaces GM# 4586871, 4601374, 4615789 This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases.
For 1953 1954 Chevrolet Cars
CHEVROLET 1953-1954 150 SER. WINDSHIELD SEAL
This windshield seal fits 1953-1954 Chevrolet Series 150 passenger cars including sedan delivery - no reveal molding. This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. Fitted gasket provides a formed, seamless seal. Designed from original part so it fits correctly. Replaces GM# 4616205, 4616476 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1953 1954 Chevrolet Cars
CHEVROLET 1962 IMPALA 2DR H/T WINDSHIELD SEAL
1962 Impala 2-door hardtop only Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1962 Chevrolet Cars
CHEVROLET 1940 WINDSHIELD SEAL - WITH REVEAL
This windshield seal fits all 1940 Chevrolet passenger cars - Series 1000 - that have reveal molding. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. Note: Designed to be used with reveal molding. Includes installation instructions. Replaces GM# 4099932 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1940 Chevrolet Cars
CHEVROLET 1941-48 WINDSHIELD SEAL (NO REVEAL)
This windshield seal fits 1941-1948 Chevrolet passenger cars - Series 1200 - models without reveal molding. Also requires 70-373 to complete installation. Refer to the Fisher Body Identification Plate on the firewall for specific Style number information. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. Replaces GM# 4116260 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
CHEVROLET 1959-60 CAR WINDSHIELD SEAL
This is a rubber Windshield Seal for 1959-1960 Chevrolet Passenger cars with reveal molding. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Inc. These channels are of the highest quality authenticity and made in the USA. Replaces GM# 4757011, 4803019 Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield. Specific Applications: 1959: All models with revel molding 1960: All except Biscayne, Brookwood and Fleetmaster.
For 1959 1960 Chevrolet Cars
CHEVROLET 1940 WINDSHIELD SEAL - NO REVEAL
This windshield seal fits 1940 Chevrolet passenger cars that do not have reveal molding - Series 1200 & 1500. Refer to the Fisher Body Identification Plate on the firewall for specific Style number information. Reveal molding is the stainless trim that inserts into the rubber windshield channel. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. Replaces GM# 4099966 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1940 Chevrolet Cars
CHEVROLET 1949-1952 WINDSHIELD SEAL - STYLELINE
This windshield seal fits 1949-1952 Chevrolet passenger cars - Series 1200 (except 1207, 1208, 1271) - models without reveal molding. Refer to the Fisher Body Identification Plate on the firewall for specific Style number information. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. Fitted gasket provides a formed, seamless seal. Designed from original part so it fits correctly. Replaces GM# 4587341, 4587641. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1949 1950 1951 1952 Chevrolet Cars
CHEVROLET 1950 OLDS 1-PIECE WINDSHIELD SEAL
This windshield seal fits 1949-1952 Chevrolet 2-Door Hardtop & Convertibles: Styles 1037 & 1067 with reveal molding . NO DIVISION BAR - FOR CUSTOM CARS ONLY. This windshield gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the front glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation. It also has the slot to accommodate the outer edge's decorative molding. This windshield seal is for the street rodder or custom car builder. Molded without the division bar so that a one-piece windshield can be installed.
For 1949 1950 1951 1952 Chevrolet Cars
CHEVROLET 1961-62 CAR WINDSHIELD VULCANIZED SEAL
This windshield seal fits 1961-1962 Chevrolet Full size except Fleetmaster & Convertible. Also fits 1962 Full size passenger except Impala 2dr Hardtop & Convertible. For models with reveal molding. Reveal molding is the stainless trim that inserts into the rubber windshield channel. This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. Replaces GM# 4813438 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA.
For 1961 1962 Chevrolet Cars
CHEVROLET 1949-52 CAR WINDSHIELD SEAL-NO REVEAL
Same applications as 25-47 no reveal This windshield seal is for the street rodder or custom car builder. Molded without the division bar so that the windshield can be "butted" together.
For 1949 1950 1951 1952 Chevrolet Cars
CHEVROLET 1931-1934 WINDSHIELD FRAME TO BODY SEAL
This is a Lower Windshield Mounting Weatherstrip for 1931-1934 Chevrolet Cabriolet & Landau Phaeton only. NOTE: this piece is 48 inches long and is made for Buick & Cadillac, which are larger autos. To be used on Chevy, this piece must be shortened in the middle to match the windshield frame. Works on 1931 Cabriolet & Landau Phaeton as a replacement piece. Replaces GM# 4034226
For 1931 1932 1933 1934 Chevrolet Cars
CHEVROLET '49-52 CONV/HT W/SHIELD SEAL-NO REV
Cars without reveal molding: Styles 1037 & 1067, 1207 & 1208. NO DIVISION BAR. This windshield seal is for the street rodder or custom car builder. Molded without the division bar so that the windshield can be "butted" together.
For 1949 1950 1951 1952 Chevrolet Cars
CHEVROLET 1949-1952 CAR WINDSHIELD SEAL-REVEAL TYPE
This windshield seal fits 1949-1952 Chevrolet passenger cars: Styles 1011, 1027, 1069,1271 models with reveal molding. Refer to the Fisher Body Identification Plate on the firewall for specific Style number information. Reveal molding is the stainless trim that inserts into the rubber windshield channel. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding. Replaces GM# 4573854, 4587340 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products, Inc. These channels are of the highest quality and made in the USA.
For 1949 1950 1951 1952 Chevrolet Cars
CHEVROLET 1949-52 CONV'T/HT WINDSHIELD SEAL
This windshield seal fits 1949-1952 Chevrolet Convertible & Hardtop models - Styles 1037 and 1067 with reveal molding. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative (reveal) molding. Fitted gasket provides a formed, seamless seal and accommodates reveal molding. Designed from original part so it fits correctly. Replaces GM# 4564079, 4573857 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products, Inc. These channels are of the highest quality and made in the USA.
For 1949 1950 1951 1952 Chevrolet Cars
CHEVROLET 1949-1951 WINDSHIELD SEAL - FLEETLINE
This windshield seal fits 1949-1951 Chevrolet Fleetline Special 2 and 4 door - No Reveal molding. Styles 1207 & 1208. Refer to the Fisher Body Identification Plate on the firewall for specific Style number information. This windshield gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit. Fitted gasket provides a formed, seamless seal. Designed from original part so it fits correctly. Replaces GM# 4585281. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1949 1950 1951 Chevrolet Cars
CHEVROLET 1949-52 FLEETLINE WINDSHIELD RUBBER
1949-52 Fleetline deluxe 2 and 4 door with reveal molding. Styles 1007 and 1008 Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1949 1950 1951 1952 Chevrolet Cars
CHEVROLET 1949-1952 WINDSHIELD HEADER SEAL-CONV
This is the windshield header seal for 1949-1952 Chevrolet convertibles. The seal is the lower or rear, to the folding top front roof bow. Replaces GM# 4566232.
For 1949 1950 1951 1952 Chevrolet Cars
CHEVROLET 1936 CONVERTIBLE WINDSHIELD SEAL
This is the windshield seal for 1936 Chevrolet Convertibles - Style #1267. This windshield gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. Note: Requires divider bar seal, our part # 70-59. Includes installation instructions. Fitted gasket provides a formed, seamless seal. Designed from original part so it fits correctly. Replaces GM# 4064618. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality and made in the USA.
For 1936 Chevrolet Cars
CHEVROLET 1963-64 POST MODEL WINDSHIELD SEAL
1963-64 All full size post models Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1963 1964 Chevrolet Cars
CHEVROLET 1949-52 STATION WAGON W'SHIELD SEAL
1949-52 Models with reveal molding. Ready to install vulcanized windshield glass channels that are manufactured for Chevrolet automobiles by Steele Rubber Products Inc. These channels are of the highest quality authenticity and made in the USA. Division bars are molded into place when required in most cases. Note: when we refer to reveal molding we mean the stainless trim usually inserted in the windshield rubber that goes around the windshield.
For 1949 1950 1951 1952 Chevrolet Cars
86 Items Found