This clip is the retainer for 1949-1952 Chevrolet passenger car center hood moldings. Seven (7) clips are required per molding. Designed to twist to lock in place. Dimensions: 9/16" Wide at top x 1-5/16" Tall x 11/16" Overall Width. Replaces GM# 3688261
This is a set of 6 clips for mounting one stainless hood side trim for 1937 Chevrolet passenger cars. These are a replacement clip used for round holes. 2 sets required per vehicle. Use to mount GR-98 Hood Side Trim.
These clips hold the NARROW hood side trim in place on all 1937-1939 Chevrolet passenger cars with slotted holes in the hood. 12 pieces in each set for two trim moldings. Dimensions: .268 Wide x .450" Long. Tab Height .300" Tab Width .300". Twist Type Clip. Replaces GM# 597522, 350538
These clips hold the WIDE hood side trim in place on all 1938 Chevrolet passenger cars with slotted holes in the hood. 12 pieces in each set for two trim moldings. Dimensions: .545" Wide x .470" Long - Tab Height .325", Tab Width .300". Replaces GM# 597523
This is a Hood Trim & Dash Trim Retaining Clip for all 1941-1946 Chevrolet trucks. This twist type clip is original for these applications. Dimensions: .450" x .450" - Tab Height .340", Tab Width .285". Twist Type Clip, Zinc plated steel. Sold each. Also see FS-2818 clip for an economical round hole replacement fastener.
This is a Universal Molding Clip with a 5/8" Wide head and 10-24 thread. Use on moldings that are 1/2 to 3/4" wide. Comes without nut. Use with FS-2558 washer nut or FS-8864 Push-on retainer.
This is a molding clip for 1967-1972 Chevrolet & GMC Fleetside Tail Light Bezel. Eight pieces required per truck. Other uses as required. For Molding Size 5/8" thru 1", Hole Size 5/16" to 1/2". Specific Applications: 1967-1968 Chevrolet Fleetside; 1967-1972 GMC Fleetside
For 1967 1968 1969 1970 1971 1972 Chevrolet Trucks
This is a Universal Molding Fastener that can be used on trim that is 3/4" to 1-3/4" wide. Dimensions of the plate: 3/8" x 1-7/8", Bolt size #10-24 x 1/2" Long. Replaces GM# 3744999
This is a Universal Molding Fastener that can be used on trim that is 1" to 2-1/2" wide. Dimensions of the plate: 11/16" x 2-17/32", Bolt size #10-24 x 3/4" Long.
This is an adhesive clip for 1969-1972 Chevrolet and GMC truck lower side moldings. This clip is designed as the original and will not bend aluminum when installing. This clip uses 3M adhesive pads of the correct thickness to hold moldings tight to the truck. Replaces GM# 3967815
This clip set is intended to attach the upper and lower quarter moldings on 1960 Impala, 2 door hardtop and convertible models. These set includes the hardware necessary to attach the upper and lower quarter moldings on ONE SIDE of the vehicle.
This clip set is intended to attach the upper and lower quarter moldings on 1959 Impala, 2 door hardtop and convertible models. One set includes the hardware necessary to attach the upper and lower quarter moldings on BOTH sides of the vehicle.
This is a Rocker Molding Mounting Clip Set for 1953-1955 Chevrolet Passenger Cars. The clips are correct for 1955, but will work on 1953-1954 as a replacement. Dimensions: 1" x 1-7/16", 10 Clips Per Set. This clip is mounted with a screw - like 1955, not a bend-over tab as was used in 1953-1954. To mount this set on 1953-1954 models, install one clip at each end by drilling a hole in the rocker in between the factory square holes. Hold the rocker molding in place on the top of the clips to insure proper alignment. Once it is determined that the alignment is correct, drill remaining holes. To mount the molding to the body, hook the top edge of the molding over the top of the mounting clips. Snap the bottom of the molding firmly down over the lower legs of the clip.
This is a Rocker Molding Mounting Clip Set for 1953-1955 Chevrolet Passenger Cars. The clips are correct for 1955, but will work on 1953-1954 as a replacement. Set does both sides. Dimensions: 1" x 1-7/16", 16 Clips Per Set. This clip is mounted with a screw - like 1955, not a bend-over tab as was used in 1953-1954. To mount this set on 1953-1954 models, install one clip at each end by drilling a hole in the rocker in between the factory square holes. Hold the rocker molding in place on the top of the clips to insure proper alignment. Once it is determined that the alignment is correct, drill remaining holes. To mount the molding to the body, hook the top edge of the molding over the top of the mounting clips. Snap the bottom of the molding firmly down over the lower legs of the clip. Ours is the only complete set of clips on the market. If you are looking for quality, this is the one to get.
These are the trim clips that hold the running board trim in place for all 1937-1938 Chevrolet passenger cars. 24 Piece Set is 20 clips and 4 spring clips - 13/16" Wide. One kit does both sides. Replaces GM# 593617
This clip set is complete for both rocker moldings for 1942-1948 Chevrolet cars, including Sedan Delivery. These are the coil type clip for use with the reproduction or original rocker moldings. Compare to GM-2271K straight clip if using with original rocker moldings.
This is the straight snap-in type clip and will not work with the reproduction rocker moldings. This set is for original rocker moldings only. Also used in these years was a coiled wire type clip - our part number for the wire clip is L-104. Compare to your original clips.
This is a Tail Light Bezel Mounting Clip & Screw Set for 1967-1972 Chevrolet & GMC Fleetside Trucks. Set is for both sides and includes 8 clips and 4 screws.
This is a universal nylon molding clip. It is designed with a pushbutton mounting and must be clipped on to the body before attaching trim. Once the clip is mounted, install molding by hooking the top side first, then snapping the bottom over the clips. For 3/8" wide moldings and 1/4" hole in body.
