This is a set of LOWER REAR motor mounts for 1954-1982 Chevrolet & GMC trucks. These mounts sit under the bell housing cross member. Also see FS-322 upper mounts. Replaces GM# 3789949, 3705447 Specific Applications: 1954-1955 (1st Series) All Commercial & Utility; 1955-1982 (2nd Series) 1/2 Ton thru 2 Ton Utility Trucks
This is a set of UPPER REAR motor mounts for 1954-1982 Chevrolet & GMC trucks. These mounts sit on top of the bell housing cross member. Also order FS-323 lower mounts. Replaces GM# 3705444 Specific Applications: 1954-1955 (1st Series) All Commercial & Utility; 1955-1982 (2nd Series) 1/2 Ton thru 2 Ton Utility Trucks
This rear seat mount reinforcement strip fits under the cargo floor of 1969-1972 Blazers and GMC Jimmies. See Diagram for placement. Dimensions: 48" X 5" X 1"
This is a left hand 1955-57 rear body mount reinforcement. The mount is located near the rear of the body and will add strength and stability to the trunk floor where it mounts the body to the frame.
This is a right hand 1955-57 rear body mount reinforcement. The mount is located near the rear of the body and will add strength and stability to the trunk floor where it mounts the body to the frame.
1940-1954 Chevrolet Car Transmission Cross Member. This kit is designed to be used with 1955 & newer Powerglide, TH 350, TH 400, THM700-R4, 4L60, MD8 Automatic Transmissions. Cut to fit the width of your frame. 4 inch drop. Bolt in and/or weld-in assembly. Will not work with manual transmission.
For 1940 1941 1942 1944 1945 1946 1947 1948 1949 1950 1951 1952 1953 1954 Chevrolet Cars
This is an Automatic Transmission Mount for 1958-1964 Chevrolet passenger cars. Bolt Dimensions: Mounting Bolts - 3-3/4" Centers, Transmission Bolts - 1-1/2" Centers. Use with TR-93 Cross member kit.
Transmission mounting at front cross-member.GM's #3704551 #3700334 #3700519. New rubber with steel core. This is a new part, no core required. One required per car. All passenger models.
This transmission mount repair kit fits 1934-1936 Chevrolet passenger cars (exc. 1934 Std) and 1935-1936 1/2 ton 3-speed transmission. This two piece unit of special soft rubber to be used with original steel channel and plate. Install rubber pads above and below the steel channel as original retaining your old steel plate and steel cap if used. Compare with your original mount before ordering.
This is a NORS (New Old Replacement Stock) transmission mount assembly for all 1937-1939 Chevrolet passenger cars - Models GA, GB, HA, HB, JA, JB. Dimensions are approximately 5" x 8" and replaces GM #593954. THIS IS A LIMITED SUPPLY ITEM AND SUBJECT TO STOCK ON HAND. Also see 60-315 for our rebuilding service for your original metal core.
This is a NORS (New Old Replacement Stock) transmission mount assembly for all 1940-1948 Chevrolet passenger cars. Replaces #756100 #3653130. This is a Limited Supply item, availability is subject to stock on hand.
For 1940 1941 1942 1944 1945 1946 1947 1948 Chevrolet Cars
This is a REVULCANIZING SERVICE ONLY. Fits 1958-1963 Chevrolet cars & trucks. New rubber vulcanized on your old steel core. Be sure to send both metal parts and allow 3 weeks. All passenger models with Power glide transmission (except 327 engine).
For 1958 1959 1960 1961 1962 1963 Chevrolet Cars and Trucks
1937-46 Insulator, plate assembly, guide, transmission support bracket. Replaces #593955. Used with 60-315 (above) from 1937- 39. Used with 60-407 (below) from 1940-46. Re-vulcanizing service only. Send in your original part with your order. Allow approximately 3 weeks for clean up, preparation and re-vulcanizing with new rubber.
For 1937 1938 1939 1940 1941 1942 1944 1945 1946 Chevrolet Cars
This is a Re-vulcanizing Service for 1948-1953 Chevrolet & GMC 1/2 Ton Trucks with 3-Speed Transmissions. This service will restore your original transmission mount to a like new original condition. GM# 3688234 Re-vulcanizing service only. Please send in your old mount and allow 3 to 4 weeks for service. Please be sure to send in all parts of the mount - including any plates or rivets that are necessary for proper assembly.
For 1948 1949 1950 1951 1952 1953 Chevrolet Trucks
1932-33 Insulator support, frame to free wheeling unit. New rubber vulcanized to your old core. Send original support assembly and allow 3 weeks. All models so equipped.
Replaces #3690416. All passenger with Power glide transmission except convertible. Send in your complete core and we will re-vulcanize with top quality rubber to new condition. Please allow 3 weeks for service.
Replaces #476015. Approximately 6" x 8". Revulcanizing service. You must send in your old steel main bracket and bottom plate. We vulcanize new rubber in our molds to give you a new insulator exactly like original. Series FC (Standard) passenger and Sedan Delivery. Allow 3 weeks for delivery.
1932-36 Pickup & Sedan Delivery. THIS IS A RE-VULCANIZING SERVICE ONLY - PUTS NEW RUBBER INTO YOUR ORIGINAL METAL CORES. Send your steel core (2 pieces per support) allow 3-4 weeks for service. FITS: 1932-1936 Pickup & Sedan Delivery ONLY. Replaces GM #368451
For 1932 1933 1934 1935 1936 Chevrolet Cars and Trucks
Transmission mounting at front cross-member. Repair #3704551 #3700334 #3700519. New rubber vulcanized to your old steel core. Send in old core and allow 3 weeks. One required per car. All passenger models.
1940-47 1/2 Ton Re-vulcanizing service only. Please send in your old mount and allow 3 to 4 weeks for service. Please be sure to send in all parts of the mount - including any plates or rivets that are necessary for proper assembly.
For 1940 1941 1942 1944 1945 1946 1947 Chevrolet Trucks
Revulcanizing service only. Please send in your old mount and allow 3 to 4 weeks for service. Please be sure to send in all parts of the mount - including any plates or rivets that are necessary for proper assembly.
This is a Six-Piece Wiper Motor Mounting Kit for 1962-1984 Chevrolet & GMC cars & trucks. Kit includes 3 rubber & metal mounting grommets and 3 hex head mounting bolts. Replaces GM# 4910180, 3824124 Specific Applications: 1962-1984 Chevy & GMC Trucks; 1963-1974 Chevrolet Cars
**THERE ARE 2 DIFFERENT MOTORS FOR THIS SERIES OF TRUCK, ONE MOTOR LAYS FLAT ON THE FIREWALL (PA-26F) AND THE OTHER STICKS OUT TOWARDS THE SEAT(PA-26). This high quality electric wiper motor is made in the USA by Newport Engineering. It is a direct bolt-in replacement for your original vacuum motor. This unit has a 2-speed heavy duty motor. It also has an automatic "park" position and uses the original wiper linkages and transmissions. Can be installed in less than an hour! The kit comes complete with wiring harness and switch.
For 1960 1961 1962 1963 1964 1965 1966 Chevrolet Trucks
