This is a 5/16" Head Split Rivet - Zinc Plated. Used to install FS-118 Hood Lace onto the radiator shell. Approximately 20 used per radiator shell. Specific Applications: 1929-1932 Passenger Cars; 1929-1933 Trucks

This is Hood Lace without Wire for 1929-1933 Chevrolet cars & trucks. Used on many GM vehicles in this era. This hood lace is held in place with split rivets FS-11683 - sold separately. This Hood Lace is sold by the foot.

This is a set of hood lace hooks to be used with the hood lace with wire insert that was used on most GM vehicles from 1929-1939, including all Chevrolet cars & trucks. Each hook is designed to grab the wire that is inserted inside the hood lace and draw it tight to insure a clean installation. These are an exact match to the original hooks. They have a threaded shaft and come with a nut for tension. Replaces GM# 355568

Not an original item but can be used on any vehicle. Comes with two rivets.

These rubber bumpers fit all 1929-1932 Chevrolet cars & trucks. They mount into the hood roll at the bottom edge of the hood side at the front and rear of the hood. We recommend gluing them in place with a small dab of clear silicone sealer to prevent them from falling out if they get bumped. Diameter of the head of the bumper is 5/16", shaft diameter 3/16", overall length 3/4".

This is a completely new reproduction of the original Cowl Hood Lace with Wire Insert that was used on most GM vehicles from 1929-1939, including all Chevrolet cars & trucks. Design & engineering took over a year to get an exact match. The material is a dark brown, close to black. Proper contours & beads that match original samples perfectly. Each strip is 3/4" Wide x 48" Long of fabric with a 52" wire inserted into it. Cut to length as required. NOTE: The hood lace is sold in individual 48" strips to fit most cowl applications. Mid-thirties cars also used this material on the radiator shell. To accommodate mid 30's vehicles where short sections are required on radiator shells, order one extra piece. ORDER TWO PIECES IF DOING A COWL AND A THIRD PIECE IF NEEDED ON THE RADIATOR SHELL. Early cars used hood lace without wire on the radiator shell. Order tension hooks AF-277 or clips set DS-106R separately. Made in the USA! Replaces GM# 374969.

This all new reproduction of the factory hood bumper stops fits all 1929 - 1931 Chevrolet cars & trucks and all 1932 trucks. These bumpers mount in the center of the hood, facing outward and mounted on the flange of the front fender. One bumper is mounted on each fender. On the driver side fender there is a wire harness clip included to hold the headlight wires to the fender. This set comes with two metal brackets with rubber bumpers and the mounting hardware ready to install. Another quality reproduction from The Filling Station. Replaces GM# 356743

1929-31 HOOD SUPPORT BRACKETS

1929-32 Passenger & 1929-33 Truck. 1EA 1/4" x 33-1/8" 2EA 3/16" x 31-5/16"

This is a BLACK 4 piece Hood Latch Set for early Chevrolet cars & trucks. They are correct for all 1931 cars & trucks and also 1932 Chevy trucks. They will work on all 1929-1932 trucks and 1929-1931 passenger cars by using the correct forked hooks on the hood (GR-150). The hooks that go on the hood are sold separately. Overall Height in relaxed position: 5-1/4" - Extended Length 6-1/4". Replaces GM# 357092, 365848. Another quality part made by The Filling Station.

This Hood Hook Set is correct for all 1931 Chevrolet cars & 1931-1932 Chevy trucks. They can be used on 1929 & 1930 cars & trucks if used with GR-149 Hood Latches. This 4-piece set is chromed. Instead of rivets to mount these hooks, we have a set of rivet head bolts

This is a CHROME 4 piece set of hood latches for early Chevrolet cars & trucks. They are correct for all 1931 cars & trucks and also 1932 Chevy trucks. They will work on all 1929-1932 trucks and 1929-1931 passenger cars by using the correct forked hooks on the hood (GR-150). The hooks that go on the hood are sold separately. Overall Height in relaxed position: 5-1/4" - Extended Length 6-1/4". Replaces GM# 357092, 365848. Another quality part made by The Filling Station.

This universal hood prop kit mounts on the radiator support "V" rod that mounts to the firewall. Used on cars & trucks with 4-piece hoods. Holds one side of the hood open at a time. These stainless kits make holding the hood open an easy task.