This is a 5/16" Head Split Rivet - Zinc Plated. Used to install FS-118 Hood Lace onto the radiator shell. Approximately 20 used per radiator shell. Specific Applications: 1929-1932 Passenger Cars; 1929-1933 Trucks

This is Hood Lace without Wire for 1929-1933 Chevrolet cars & trucks. Used on many GM vehicles in this era. This hood lace is held in place with split rivets FS-11683 - sold separately. This Hood Lace is sold by the foot.

This is a set of hood lace hooks to be used with the hood lace with wire insert that was used on most GM vehicles from 1929-1939, including all Chevrolet cars & trucks. Each hook is designed to grab the wire that is inserted inside the hood lace and draw it tight to insure a clean installation. These are an exact match to the original hooks. They have a threaded shaft and come with a nut for tension. Replaces GM# 355568

Not an original item but can be used on any vehicle. Comes with two rivets.

This is a completely new reproduction of the original Cowl Hood Lace with Wire Insert that was used on most GM vehicles from 1929-1939, including all Chevrolet cars & trucks. Design & engineering took over a year to get an exact match. The material is a dark brown, close to black. Proper contours & beads that match original samples perfectly. Each strip is 3/4" Wide x 48" Long of fabric with a 52" wire inserted into it. Cut to length as required. NOTE: The hood lace is sold in individual 48" strips to fit most cowl applications. Mid-thirties cars also used this material on the radiator shell. To accommodate mid 30's vehicles where short sections are required on radiator shells, order one extra piece. ORDER TWO PIECES IF DOING A COWL AND A THIRD PIECE IF NEEDED ON THE RADIATOR SHELL. Early cars used hood lace without wire on the radiator shell. Order tension hooks AF-277 or clips set DS-106R separately. Made in the USA! Replaces GM# 374969.

This STEEL rear hood hinge hold down bracket is used to attach the hood hinge to the cowl on 1933 Chevrolet Passenger vehicles and well as 1934-1946 Chevrolet and GMC trucks. Bolt centers are 1-1/2". Specific Applications: 1933 Passenger Vehicles; 1934-1946 Chevrolet Trucks; 1939-1946 GMC Trucks

This STAINLESS STEEL rear hood hinge hold down bracket is used to attach the hood hinge to the cowl on 1933 Chevrolet Passenger vehicles and well as 1934-1946 Chevrolet and GMC trucks. Specific Applications: 1933 Passenger Vehicles 1934-1946 Chevrolet/GMC Trucks

This hood hinge hold down mounts to the radiator shell on 1932 Chevrolet Passenger cars and 1933 Chevy Trucks. This hold down is stamped in stainless. Made in the USA!

1929-32 Passenger & 1929-33 Truck. 1EA 1/4" x 33-1/8" 2EA 3/16" x 31-5/16"

This is a 6-piece set of beautifully chromed Hood Door Finger Pulls for 1933 Chevrolet Master passenger cars. These beautiful reproductions of the original chrome pieces will make your 1933 Chevy shine like it should! The precision die-cast pulls are triple chrome plated to a show quality finish. They are super detailed and absolutely stunning! 1933 Pulls are sold in sets of six (6) pieces. They come with mounting screws ready to install. In stock and ready for immediate shipment. You can buy with confidence as we have been serving the hobby since 1979 and we are the manufacturer of this quality reproduction. Replace those old original, pitted pulls with this show quality set. Get yours today! Overall Length 3-1/4" Long. Replaces GM# 370637

This is a set of Hood Latch Bracket for 1932 Chevrolet Passenger Cars & 1933 Chevrolet Trucks. Set of four pieces for the Cowl & Radiator Shell. These are the brackets that hold the ends of the locking rods in place. One set required per vehicle.

This universal hood prop kit mounts on the radiator support "V" rod that mounts to the firewall. Used on cars & trucks with 4-piece hoods. Holds one side of the hood open at a time. These stainless kits make holding the hood open an easy task.