This is a windshield wiper arm for 1949-1955 Chevrolet & GMC cars & trucks. Specify Left or Right when ordering Replaces GM# 3703494 Specific Applications: 1949-1954 Passenger (exc. Hardtop & Convertible); 1954-1955 (1st Series) Chevy & GMC Trucks
For 1949 1950 1951 1952 1953 1954 1955 Chevrolet Cars and Trucks
This is a windshield wiper arm for 1949-1955 Chevrolet & GMC cars & trucks. Specify Left or Right when ordering Replaces GM# 3703494 Specific Applications: 1949-1954 Passenger (exc. Hardtop & Convertible); 1954-1955 (1st Series) Chevy & GMC Trucks
For 1949 1950 1951 1952 1953 1954 1955 Chevrolet Cars and Trucks
This universal wiper arm is polished stainless steel with an adjustable range of 6" to 8" long. They have a "J" Hook end to accept wiper blades made especially for this type of hook. It clamps onto a 1/4" shaft and works with the following wiper motors: VT-6VSS, VT-12VSS, VT-6VK AND VT-12VK. This arm is designed for use with VT-66 or VT-67 wiper blades with "J" Hook opening.
This universal wiper arm is polished stainless steel with an adjustable range of 8" to 12" long. They have a "J" Hook end to accept wiper blades made especially for this type of hook. It clamps onto a 1/4" shaft and works with the following wiper motors: VT-6VSS, VT-12VSS, VT-6VK AND VT-12VK. This arm is designed for use with VT-66 or VT-67 wiper blades with "J" Hook opening.
These are new chrome wiper transmission bezels that fit 1955-1959 (2nd Series) Chevrolet trucks. The copper tube extension is for the accessory washer nozzles. These are available separately, order TR-108.
This is a pair of Chrome Windshield Wiper Transmission Bezels for 1955-1956 Chevrolet Passenger Cars (exc 1955 150 Series). Set includes 2 bezels, 2 washer nozzles, and 2 lock nuts. See also L-136 for 1955 150 Series.
This is a pair of Chrome Windshield Wiper Transmission Bezels for 1955 Chevrolet 150 Series Passenger Cars. Set includes 2 bezels, 2 washer nozzles, and 2 lock nuts. See also L-136A for other than 150 Series.
This is a wiper blade insert refill for 1955-1959 Chevrolet & GMC cars & trucks. The blade refill is 12 inches long. Replaces GM# 566510 Specific Applications: 1955-1957 Passenger; 1955-1959 (2nd Series) Chevy & GMC Trucks
For 1955 1956 1957 1958 1959 Chevrolet Cars and Trucks
This is a wiper blade insert refill for 1949-1955 Chevrolet & GMC cars & trucks. The blade refill is 11 inches long. Replaces GM# 373355, 557979 Specific Applications: 1949-1954 Passenger; 1954-1955 (1st Series) Chevy & GMC Trucks
For 1949 1950 1951 1952 1953 1954 1955 Chevrolet Cars and Trucks
This complete windshield wiper blade fits 1949-1955 Chevrolet & GMC cars & trucks. The overall length of the blade is 11 inches long. Designed to fit with our TR-28 Wiper Arms. Replaces GM# 561094, 561268, 986882 Specific Applications: 1949-54 Chevrolet Passenger cars 1954-55 (1st Series) Chevy & GMC Trucks
For 1949 1950 1951 1952 1953 1954 1955 Chevrolet Cars and Trucks
This is a windshield wiper blade assembly for 1955-1959 Chevrolet & GMC cars & trucks. Blade assembly is 12" long. Use with TR-24 & TR-25 Wiper Arms. Replaces GM# 3733356 Specific Applications: 1955-1957 Passenger (exc Electric Wiper); 1955-1959 (2nd Series) Truck
For 1955 1956 1957 1958 1959 Chevrolet Cars and Trucks
This original reproduction windshield wiper switch fits 1955-1956 Chevrolet passenger vehicles. This switch comes complete with a new stainless steel cable and sheath and can operate both electric and vacuum wiper motors. The body of this switch has a --3/16" overall depth. NOTE: This switch is not compatible with the original 1955 accessory windshield washer kit.
Our modern vehicles have spoiled us to rely on the safety of intermittent wipers. Now you can have this "modern" convenience in your vintage car or truck. This switch is designed to work on all Newport Engineering wiper motors to make your old car as safe as your modern car. NOTE: Will NOT Work on stock electric wiper motors!
This is the 1954-55 1st Series pickup wiper motor transmissions for left and right side. Has linkage from wiper motor to the transmissions that stick trough the cowl. Overall length is 27-1/2" long.
This wiper motor transmission set fits VACUUM & ELECTRIC wiper motors in 1955-1959 Chevrolet and GMC trucks. The set includes the links and pivots from the wiper motor to the splined output shafts that the wiper arms attach to. In 1955, fits 2nd Series only. Fits left and right. Replaces GM# 3730483, 3722488 Specific Applications: 1955-1957 (2nd Series) Trucks - Vacuum or Electric; 1958-1959 Trucks - Vacuum ONLY
In 1955, used on 2nd Series only. This kit completely replaces the factory wiper system. It comes with a 12 volt, ten amp, two-speed electric motor. Complete with bracketing, linkage arms, wiper transmissions, wiring and switch. Designed to fit neatly under the dash. Order this kit if you want standard two-speed wiper operation. Also available is the same kit with wiper delay switch - see PA-34D. Use with your original wiper arms, blades & chrome trim. A top quality product Made in the USA!
This kit completely replaces the factory type "spool & cable" wiper system. It comes with a 12 volt, ten amp, two-speed electric motor. Complete with bracketing, linkage arms, wiper transmissions, wiring and switch. Designed to fit neatly under the dash. For those that want to maintain original appearance, the original motor can be left in place in the engine compartment. Order this kit if you want standard two-speed wiper operation. Also available is the same kit with wiper delay switch - see PA-31D. Use with your original wiper arms, blades & chrome trim. A top quality product Made in the USA!
In 1955, used on 1st Series only. DO NOT USE WITH IN-DASH RADIO. This kit completely replaces the factory vacuum wiper system. It comes with a 12 volt, ten amp, two-speed electric motor. Complete with bracketing, linkage arms, wiper transmissions, wiring and switch. Designed to fit neatly under the dash. Order this kit if you want standard two-speed wiper operation. Also available is the same kit with wiper delay switch - see PA-33D. Use with your original wiper arms, blades & chrome trim. A top quality product Made in the USA! The RainGear system will fit all 1947 to 1954 Chevrolet and GMC trucks with the following exceptions: On 1954 trucks only, the stock defroster ducts will not clear our system. When installing our system into a 54 either use the ducts from a 47-53 truck or ducts from one of the aftermarket A/C system suppliers. Original radios in the upper dash board mount location will not clear our system. We have one report of an aftermarket radio interfering as well. Cross-mount master cylinders likely wont fit with our RainGear system installed. The kit comes complete less assembly lube, arms and blades, escutcheons and model-specific knobs for the switch. All those stock pieces will fit on our system. Escutcheons are the exterior trim bezels which cover the pivot posts in the cowl. Please note that the RainGear unit cannot be controlled by any General Motors column-mounted wiper switches. You must use the included switch. This is due to the fact that GM switches control the wiper motor via the ground wire and our systems must be controlled by switching the positive wire.
For 1947 1948 1949 1950 1951 1952 1953 1954 1955 Chevrolet Trucks
In 1955, used on 2nd Series only. This kit completely replaces the factory wiper system. It comes with a 12 volt, ten amp, two-speed electric motor. Complete with bracketing, linkage arms, wiper transmissions, wiring and switch. Designed to fit neatly under the dash. Order this kit if you want wiper delayed, two-speed wiper operation. Also available is the same kit without wiper delay switch - see PA-34. Use with your original wiper arms, blades & chrome trim. A top quality product Made in the USA!
This kit completely replaces the factory type "spool & cable" wiper system. It comes with a 12 volt, ten amp, two-speed electric motor. Complete with bracketing, linkage arms, wiper transmissions, wiring and switch. Designed to fit neatly under the dash. For those that want to maintain original appearance, the original motor can be left in place in the engine compartment. Order this kit if you want wiper delayed, two-speed wiper operation. Also available is the same kit without wiper delay switch- see PA-31. Use with your original wiper arms, blades & chrome trim. A top quality product Made in the USA!
In 1955, used on 1st Series only. DO NOT USE WITH IN-DASH RADIO. This kit completely replaces the factory vacuum wiper system. It comes with a 12 volt, ten amp, two-speed electric motor. Complete with bracketing, linkage arms, wiper transmissions,wiring and switch. Designed to fit neatly under the dash. Order this kit if you want wiper delayed, two-speed wiper operation. Also available is the same kit without wiper delay switch - see PA-33. Use with your original wiper arms, blades & chrome trim. A top quality product Made in the USA! The RainGear system will fit all 1947 to 1954 Chevrolet and GMC trucks with the following exceptions: On 1954-55 trucks only, the stock defroster ducts will not clear our system. When installing our system into a 54 either use the ducts from a 47-53 truck or ducts from one of the aftermarket A/C system suppliers. Original radios in the upper dash board mount location will not clear our system. We have one report of an aftermarket radio interfering as well. Cross-mount master cylinders likely wont fit with our RainGear system installed. The kit comes complete less assembly lube, arms and blades, escutcheons and model-specific knobs for the switch. All those stock pieces will fit on our system. Escutcheons are the exterior trim bezels which cover the pivot posts in the cowl. Please note that the RainGear unit cannot be controlled by any General Motors column-mounted wiper switches. You must use the included switch. This is due to the fact that GM switches control the wiper motor via the ground wire and our systems must be controlled by switching the positive wire.
For 1947 1948 1949 1950 1951 1952 1953 1954 1955 Chevrolet Trucks
These wiper transmission hold down chrome nuts mount on the wiper transmissions to mount them on the cowl. These fit all 1947-1959 Chevrolet & GMC trucks.
For 1947 1948 1949 1950 1951 1952 1953 1954 1955 1956 1957 1958 1959 Chevrolet Trucks
These wiper savers are a chrome bullet that fits over the wiper transmission splines for displaying at car shows. Sold in pairs, they have a set screw to hold them in place. Approximate Height 1.5"
This is a pair of Wiper Savers - Custom Chrome Caps for any vehicle. Made specifically to remove windshield wiper arms & blades for car shows. Super nice chrome plating. Made in the USA!
This is a universal 6-VOLT Windshield Wiper Motor with Stainless Housing - NO SWITCH. This motor requires an external control switch to operate. NOTE: This motor will not work on GM vehicles with crank up windshields unless the crank mechanism is permanently removed. The shaft is 5" long and the kit includes instructions for shortening the shaft. The wiper motor has an automatic self-parking feature and a 110 degree sweep For replacement Slot Type Wiper Arms see: VT-60 (adjustable 6"-8"); VT-61 (adjustable 8"-12"). Slot Type Wiper Blades see: VT-62 8" Blade; VT-63 11" Blade. For replacement J-Hook Type Wiper Arms see: VT-64 (adjustable 6"-8"); VT-65 (adjustable 8"-12"). J-Hook Type Wiper Blades see: VT-66 6" Blade; VT-67 10" Blade; AF-341SR 8-1/4".
THE SHAFT IS 5" LONG AND INCLUDES INSTRUCTIONS FOR SHORTENING THE SHAFT. THIS WIPER MOTOR HAS AN AUTOMATIC SELF PARK AND A 110 DEGREE SWEEP. USE WITH WIPER ARMS VT-60, VT-61, VT-64, OR VT-65 AND WIPER BLADES VT-62, VT-63, VT-66, AF-341SR, OR VT-67.
This is a universal 6-VOLT Windshield Wiper Motor with Black Housing - BUILT-IN ON/OFF SWITCH. The shaft is 3-1/4" long and the kit includes instructions for shortening the shaft down to 2-1/2" long. The wiper motor has an automatic self-parking feature and a 110 degree sweep. Mounting holes are 3-5/8" on center. Machined to accept AF-320 and AF-345 Wiper Arms for stock applications. NOTE: This motor will not work on GM vehicles with crank up windshields unless the crank mechanism is permanently removed. For replacement Slot Type Wiper Arms see: VT-60 (adjustable 6"-8"); VT-61 (adjustable 8"-12"). Slot Type Wiper Blades see: VT-62 8" Blade; VT-63 11" Blade. For replacement J-Hook Type Wiper Arms see: VT-64 (adjustable 6"-8"); VT-65 (adjustable 8"-12"). J-Hook Type Wiper Blades see: VT-66 6" Blade; VT-67 10" Blade; AF-341SR 8-1/4".
This is a universal 12-VOLT Windshield Wiper Motor with Black Housing - BUILT-IN ON/OFF SWITCH. The shaft is 3-1/4" long and the kit includes instructions for shortening the shaft down to 2-1/2" long. The wiper motor has an automatic self-parking feature and a 110 degree sweep. Mounting holes are 3-5/8" on center. Machined to accept AF-320 and AF-345 Wiper Arms for stock applications. NOTE: This motor will not work on GM vehicles with crank up windshields unless the crank mechanism is permanently removed. For replacement Slot Type Wiper Arms see: VT-60 (adjustable 6"-8"); VT-61 (adjustable 8"-12"). Slot Type Wiper Blades see: VT-62 8" Blade; VT-63 11" Blade. For replacement J-Hook Type Wiper Arms see: VT-64 (adjustable 6"-8"); VT-65 (adjustable 8"-12"). J-Hook Type Wiper Blades see: VT-66 6" Blade; VT-67 10" Blade; AF-341SR 8-1/4".
This is a universal 6-VOLT Windshield Wiper Motor with Stainless Housing - NO SWITCH. This motor requires an external control switch to operate. The kit comes with an adjustable length SLOTTED Adjustable Wiper Arm that is 7-1/4" to 8-1/2" long from the pivot attachment. Slot Style Wiper blade included in the kit is 8" long. The shaft is 2.5" long. The wiper motor has an automatic self-parking feature and a 110 degree sweep. For replacement Slot Type Wiper Arms see: VT-60 (adjustable 6"-8"); VT-61 (adjustable 8"-12"). Slot Type Wiper Blades see: VT-62 8" Blade; VT-63 11" Blade. For replacement J-Hook Type Wiper Arms see: VT-64 (adjustable 6"-8"); VT-65 (adjustable 8"-12"). J-Hook Type Wiper Blades see: VT-66 6" Blade; VT-67 10" Blade; AF-341SR 8-1/4". NOTE: This motor kit will not work with early 1925-1932 Chevy cars with crank up windshields.
This is a Universal 12-Volt Wiper Motor with Stainless Housing. Motor comes with wiper arm and blade. The shaft is 5" long and includes instructions for shortening the shaft. This wiper motor has an automatic self park and a 110 degree sweep. Motor overall depth is 3-1/4". For replacement wiper arms see VT-60, VT-61, VT-64 or VT-65. Replacement wiper blades see VT-62, VT-63, VT-66, AF-341SR or VT-67. NOTE: WILL NOT WORK ON EARLY GM VEHICLES WITH CRANK-UP WINDSHIELDS.
In 1955, fits 1st Series only. This high quality electric replacement is a direct bolt - in for your original vacuum motor. A big improvement over the motors that were previously available - this motor is a 2-speed heavy duty motor. It also has an automatic park position and uses the original wiper linkages and transmissions. Can be installed in less than an hour! Complete with wiring harness. Note: If you are using original wiper transmission linkage with this motor, you must remove the bushing in the end of the transmission linkage and use the nylon bushings included with the wiper motor kit.
1955-1957 (2nd Series) Chevrolet Truck Windshield Wiper Motor. This high quality electric wiper motor is made in the USA by Newport Engineering. It is a direct bolt-in replacement for your original vacuum or electric wiper motor. This unit has a 2-speed heavy duty motor. It also has an automatic "park" position and uses the original wiper linkages and transmissions. Can be installed in less than an hour! The kit comes complete with wiring harness and switch.
This high quality electric wiper motor is made in the USA by Newport Engineering. It is a direct bolt-in replacement for your original vacuum motor. This unit has a 2-speed heavy duty motor. It also has an automatic "park" position and uses the original wiper linkages and transmissions. Can be installed in less than an hour! The kit comes complete with wiring harness and switch.
This high quality electric wiper motor is made in the USA by Newport Engineering. It is a direct bolt-in replacement for your original vacuum motor. This unit has a 2-speed heavy duty motor. It also has an automatic "park" position and uses the original wiper linkages and transmissions. Can be installed in less than an hour! The kit comes complete with wiring harness and switch.
Note: In 1955 trucks, used on 1st Series only. This high quality electric wiper motor is made in the USA by Newport Engineering. It is a direct bolt-in replacement for your original vacuum motor. This unit has a 2-speed heavy duty motor. It also has an automatic "park" position and uses the original wiper linkages and transmissions. Can be installed in less than an hour! The kit comes complete with wiring harness and switch.
